Product Description
The LeafsOut Gutter Protection System consists of three main components: a front anodized aluminum drip edge; a stainless steel V-Bend mesh filter mesh; and a water siphon control strip under the mesh. This type of gutter guard can be installed on various gutter types such as Ogee, half round, fascia, curved, box and many type of roofs such as asphalt shingle, wood shake, flat tile, Spanish tile and stone coated steel. LeafsOut's specifications were uniquely designed so that it simply slips under the roof shingles and rests on top of the roof-deck/water-barrier (tar paper) to "clamp" the gutter guard in place and stabilize its structure. The solid aluminum front fits snug to the front lip of the gutter via three self-tapping screws for each four foot length section. LeafsOut should be installed at the same pitch as the roof (up to a 6/12 pitch) to get the best performance of debris shedding off.
This is a 6" sample piece to make sure it fits on your existing gutter.
Eliminates gutter cleaning forever!
Easy installation
Handles over 100 inches of hourly rainfall!
Fits on existing rain gutters, no need to replace existing rain gutters.
Barely visible from the ground!
Fits on virtually any existing rain gutter and roof type.
The lowest cost stainless steel gutter guard protection available anywhere
Keeps out wasps and other pests
Filtered water can also be used in rainwater harvesting!
Will not degrade with exposure to the suns UV rays.
Does not require replacement of existing gutters!
Includes self tapping screws that easily screw through the aluminum front edge into the gutter.
List Price :
$1.35Price : $1.35
You Save : -
* Special discount only for limited time
Product Feature
- Micro Mesh is consistently rated the best overall gutter guard!
- Eliminates gutter cleaning and keeps out wasps and other pests, even sand
- Barely visible from the ground! Fits on virtually any existing rain gutter and roof type.
- The only Micro-Mesh gutter guard that YOU CAN INSTALL YOURSELF!
- Does not require replacement of existing gutters! Fits 5" rain gutters.
Maybe you should visit the following website to get a better price and specification details
14 of 14 people found the following review helpful.
A little purchase before a big one.
By Dan Bortz
From everything that I have read, this is a good product.
That said, I wanted to judge for myself how strong and how well it works so I ordered a sample.
One of my big concerns was whether it could handle a snow load without deflecting or at least much.
The ridges give it incredible strength. It will flex but the gutters will come off of the house before the screens sag more than a quarter of an inch.
I was also concerned about the screens clogging. I scooped a bunch of the grit and slime out of one of my gutters and smeared it onto the test piece.
Most of it washed away. Some stuff did sit at the bottom edge but I was impressed enough to order 300 feet to try it on the house.
I will post a review again after I get it installed.
3 of 3 people found the following review helpful.
The ONLY gutter filter to buy!
By Yardbird
Don't waste your time and money with other gutter filters! This stainless steel micro-mesh screen does everything you are looking for. It keeps out everything, including small needles and even asphalt shingle grit. The leaf guard rounded type gutter filter not only doesn't keep out small leaves and needles, it makes it harder to clean them out once they are in there. The foam type (which I tried first, starts degrading and crumbling after about a year. Plus, squirrels pull it out looking for seeds and small nuts.
These stainless steel screens are sturdy and edged with aluminum strips that can easily be trimmed with a pair of good sheet metal snips and vise-grips. The screen cuts easily with a good pair of scissors. A word of advice: use high quality tools. Cheap tools will frustrate you as they end up bending the aluminum instead of snipping, and stretching the screen instead of cutting (snips don't cut the screen well, scissors do). I have wooden gutters and while these are designed to easily install on aluminum or vinyl gutters, they work perfectly on wooden gutters as well. They don't have pre-drilled holes, but that is a plus, because you will want to place your fasteners where they will be the most advantageous. You'll need a drill, snips, good scissors, vise-grips, screwdriver, tape measure and sharpie.
You will be impressed, as am I. Good luck!
0 of 0 people found the following review helpful.
Worth ordering before purchasing a kit
By Retired and Loving It
Wasn't sure which size I would need so ordered one 5" and one 7" to make sure before ordering the 25ft kit. For the price, it is worth spending a few dollars to know for sure what is required. Also, gave me a real idea of the construction of the sections and how to install before hand.
No comments:
Post a Comment